Properties of hydrated cement with complex additive

The paper presents the results of physical and chemical studies of hardening products in the cement-complex additive-water system. The choice of the modifying additive is based on the structural and chemical affinity of the additive fragments with cement, which includes highly dispersed Tarkosil Ts-38 microsilica and MT-600 peat additive. The synergistic effect of the complex additive leads to a significant improvement in the performance characteristics of hydrated cement: strength, frost resistance, water resistance, and others. Physicochemical analysis shows that the introduction of the complex additive increases the density of hydrated cement due to the formation of low-basic hydrated silicates and their kinds, such as afwillite, foshagite, and truscottite.

1. Rana Md Nasim, Islam Md Nazrul, Nath Suresh Kumar, Das Atanu Kumar, Ashaduzzaman Md, Shams Md Iftekhar. Influence of chemical additive on the physical and mechanical properties of cement-bonded composite panels made from jute stick. Journal of Building Engineering. 2020. DOI: 10.1016/j.jobe.2020.101358.

2. Gorshkova A.V. Sukhie stroitel'nye smesi s modifitsiruyushchei dobavkoi na osnove torfa: dissertatsiya na soiskanie uchenoi stepeni kandidata tekhnicheskikh nauk [Dry building mixes with peat-based modifying additive. PhD Thesis]. Tomsk, 2015 161 p. (rus)

3. Zaprudnov V., Sanaev V., Karpachev S., Levushkin D., Gorbacheva G. Materials science forum. 2019. V. 972. Pp. 69–76. DOI: 10.4028/www.scientific.net/MSF.972.69.

4. Azadi Mohammad Reza, Taghichian Ali, Taheri Ali. Optimization of cement-based grouts using chemical additives. Journal of Rock Mechanics and Geotechnical Engineering. 2017. V. 9. No. 4. Pp. 623–637.

5. Kopanitsa N.O., Sarkisov Yu.S., Dem'yanenko O.V. Primenenie nanodispersnogo kremnezema v proizvodstve stroitel'nyh smesej [Nanodispersed silicon dioxide used in the production of mix mortars]. Vestnik of Tomsk State University of Architecture and Building. 2016. No. 5 (58). Pp. 140−150. (rus)

6. Smyatskaya J., Voropai L., Sinitsyn A., Tikhanovskaya G., Yukhtarova O. Technology for producing peat heat-insulating boards using organosilicon polymers. E3S Web of Conferences, EDP Sciences. 2020. 4/15. 161. Pp. 1–5.

7. Dem'yanenko O.V., Kopanitsa N.O., Sorokina E.A. Vliyanie dobavki termomodifitsirovannogo torfa na tekhnologicheskie svoistva stroitel''nykh smesei dlya 3D-pechati [Performance characteristics of 3D printing construction mixes depending on thermally-modified peat additive]. Vestnik Tomskogo gosudarstvennogo arkhitekturno-stroitel'nogo universiteta – Journal of Construction and Architecture. 2018. V. 20. No. 4. Pp. 122–134. (rus)

8. Koren'kova S.F. Dobavki k betonam [Additives to concrete]. In: Tsementy, betony, stroitel'nye rastvory i sukhie smesi. Chast' I. Saint-Petersburg: Professional, 2007. Pp. 236−265. (rus)

9. Kopanitsa N.O., Sarkisov Yu.S., Kudyakov A.I. Stenovye stroitel'nye materialy na osnove modifitsirovannykh torfov Sibiri: monografiya. Tomsk [Wall materials based on modified peat of Siberia]. Tomsk: TSUAB, 2013. 295 p. (rus)

10. Kopanitsa N., Sarkisov Y., Gorshkova A., Demyanenko O. Additives for Cement Compositions Based on Modified Peat. AIP Conference Proceedings. 2016. 1698. 070015. 070015-0-070015-5.

11. Kramar L.Ya., Trofimov B.Ya., Gamalii E.A., Chernykh T.N., Zimich V.V. Modifikatory tsementnykh betonov i rastvorov (Tekhnicheskie kharakteristiki i mekhanizm deistviya) [Modifiers of cement concrete and solutions (Specifications and operation)]. Chelyabinsk: Iskra-Profi, 2012. 202 p. (rus)