PERFORMANCE CHARACTERISTICS OF 3D PRINTING CONSTRUCTION MIXES DEPENDING ON THERMALLYMODIFIED PEAT ADDITIVE
https://doi.org/10.31675/1607-1859-2018-20-4-122-134
Abstract
The paper presents the research results on the development of scientifically valid compositions of 3D printing construction mixes with improved performance characteristics. To regulate the physical, mechanical and technological properties of cement-based mixes, thermallymodified peat additive MT-600 is developed. The paper studies the world experience in the construction additive technology field. The experimental results are presented for cement paste and construction mixes with MT-600 additive for 3D printing. It is established that using the proposed fine additive increases the strength of the cement paste at early stages of hardening, which is the determining factor in the formation of building and technical characteristics for 3D printing. The X-ray phase analysis is carried out for the new composition of cement paste modified with MT-600 additive, which allows studying characteristics of the structure and properties of construction mixes during the hardening process.
About the Authors
O. V. Dem'yanenko
Tomsk State University of Architecture and Building
Russian Federation
Research Assistant
Russian Federation
Research Assistant
N. O. Kopanitsa
Tomsk State University of Architecture and Building
Russian Federation
DSc, Professor
Russian Federation
DSc, Professor
E. A. Sorokina
Tomsk State University of Architecture and Building
Russian Federation
Research Assistant
Russian Federation
Research Assistant
References
1. Warszawski A., Navon R. Implementation of robotics in building: Current status and future prospects. Journal of Construction Engineering and Management. 1998. No. 124 (1). Pp. 31–41.
2. Ibrahim M.I. Estimating the sustainability returns of recycling construction waste from building projects. Sustainable Cities and Society. 2016. No. 23. Pp. 78–93.
3. Chen L., et al. The research status and development trend of additive manufacturing technology. The International Journal of Advanced Manufacturing Technology. 2016. Pp. 1–10.
4. Val'ter A.V. Posloinyi sintez armirovannykh ob"emnykh izdelii [Layer-by-layer synthesis of reinforced 3D products]. Gornyi informatsionno-analiticheskii byulleten' (nauchnotekhnicheskii zhurnal). 2011. V. 2. No. 12. Pp. 222–229. (rus)
5. Kablov E.N. Strategicheskie napravleniya razvitiya materialov i tekhnologii ikh pererabotki na period do 2030 goda [Strategic development and processing technologies of materials till 2030]. Aviatsionnye materialy i tekhnologii. 2012. No. 5. Pp. 7–17. (rus)
6. Gálvez J.A. Not just a pretty face: Three-dimensional printed custom airway management devices. 3D Printing and Additive Manufacturing. 2016. V. 3. No. 3. Pp. 160–165. (rus)
7. Barazanchi A. Additive Technology: update on current materials and applications in dentistry. Journal of Prosthodontics. 2016.
8. Kumar L.J. Nair current trends of additive manufacturing in the aerospace industry. Advances in 3D Printing & Additive Manufacturing Technologies. 2016. Pp. 39–54.
9. Kreiger M.A., MacAllister B.A., Wilhoit J.M. Case The current state of 3D printing for use in construction. Proc. Conference on Autonomous and Robotic Construction of Infrastructure. Ames, Iowa, 2015. Pp. 149–158.
10. Huang S.H., Liu P., Mokasdar A., Hou L. Additive manufacturing and its societal impact: a literature review. International Journal of Advanced Manufacturing Technology. 2013. V. 67. No. 5–8. Pp. 1191–1203.
11. Udodov S.A., Belov F.A., Zolotukhina A.E. 3D-pechat' v stroitel'stve: novoe napravlenie v tekhnologii betona i sukhikh stroitel'nykh smesei. Sbornik statei pobeditelei VI Mezhdunarodnoi nauchno-prakticheskoi konferentsii (Proc. 6th Int. Sci. Conf. ‘3D Printing in Construction: New Trend in Concrete Technology and Dry Mixes’). G.Yu. Gulyaev, Ed. Nauka i Prosveshchenie, 2017. (rus)
12. Litovkin S.V., Pet'kova Yu.R. Ispol'zovanie 3D pechati v mashinostroenii i stroitel'stve. Mezhdunarodnaya nauchno-prakticheskaya konferentsiya ‘Aktual'nye problemy sovremennogo mashinostroeniya’ (Proc. Int. Sci. Conf. ‘Relevant Problems of Modern Engineering’). 2015. Pp. 433–435. (rus)
13. Grakhov V.P., Mokhnachev S.A., Borozdov O.V. Vliyanie razvitiya 3D-tekhnologii na ekonomiku stroitel'stva. Fundamental'nye issledovaniya [3D technology effect on construction economy]. 2014. No. 11–12. Pp. 2673–2676. (rus)
14. Hager I., Golonka A., Putanowicz R. 3D printing of buildings and building components as the future of sustainable construction? Procedia Engineering. 2016. No. 151. Pp. 292–299.
15. Lloret E., et al. Complex concrete structures: Merging existing casting techniques with digital fabrication. Computer-Aided Design. 2015. No. 60. Pp. 40–49.
16. Le T.T., et al. Hardened properties of high-performance printing concrete. Cement and Concrete Research. 2012. V. 42. Pp. 558–566.
17. Bazhenov Yu.M. Tekhnologiya betona [Concrete technology]. Moscow: ASV, 2002. 500 p. (rus)
18. Sarkisov Yu.S., Kopanitsa N.O. O nekotorykh aspektakh primeneniya nanomaterialov i nanotekhnologii v stroitel'stve [Nanomaterials and nanotechnologies in construction]. Vestnik of Tomsk State University of Architecture and Building. 2012. No. 4. Pp. 226–234. (rus)
19. Korolev E.V., Bazhenov Yu.M., Beregovoi V.A. Modifitsirovanie stroitel'nykh materialov nanouglerodnymi trubkami i fullerenami [Construction materials modified by nanotubes and fullerenes]. Stroitel'nye materialy. 2006. No. 8. Pp. 2–4. (rus)
20. Guvalov A.A. Vliyanie organomineral'noi dobavki na rannyuyu gidratatsiyu tsementa [Or-ganomineral additive and cement hydration]. Stroitel'nye materialy. 2013. No. 9. Pp. 94–95. (rus)
21. Berdov G.I. Vliyanie vida i kolichestva mineral'nykh dobavok na prochnost' tsementnogo kamnya [Mineral additive amount and strength of cement paste]. Mezhdunarodnyi zhurnal prikladnykh i fundamental'nykh issledovanii. 2010. No. 9. Pp. 87–91. (rus)
22. Kopanitsa N., Demyanenko O., Sarkisov Y., Gorshkova A. Additives for cement compositions based on modified peat. AIP Conference Proceedings. 2016. 1698. P. 070015.
23. Kopanitsa N.O., Sarkisov Yu.S, Abzaev Yu.A. Quantitative phase analysis of modified hardened cement paste. IOP Conf. Series: Earth and Environmental Science. 2017. V. 87. P. 092008.
24. Kopanitsa N., Sarkisov Y., Sorokina E., Demyanenko O. Mortars for 3D printing. MATEC Web of Conferences. 2018. V. 143. P. 02013.
25. Klopotov V.D., Kopanitsa N.O. New organo-mineral peat-based admixtures for cement compositions. International Conference on Mechanical Engineering, Automation and Control Systems (MEACS). 2015. Pp. 1–3.
26. Kopanitsa N., Kudyakov A., Kovaleva M., Kopanitsa G. System approach to peat raw materials for production of building materials. IOP Conference Series: Materials Science and Engineering Advanced Materials in Construction and Engineering. Ser. „International Scientific Conference of Young Scientists: Advanced Materials in Construction and Engineering‟. 2015. P. 012011.
27. Kopanitsa N.O., Kasatkina A.V., Sarkisov Yu.S. Novye organomineral'nye dobavki na osnove torfa dlya tsementnykh sistem [New organomineral peat additives for cement systems]. Stroitel'nye materialy. 2015. No. 4. Pp. 93–96. (rus)
28. Kopanitsa N.O., Sarkisov Yu.S., Kasatkina A.V. Effektivnye organomineral'nye dobavki na osnove mestnogo syr'ya [Efficient organomineral agents based on local raw materials]. Vestnik of Tomsk State University of Architecture and Building. 2013. No. 4 (41). Pp. 184–190. (rus)
29. Kopanitsa N.O., Kudyakov A.I., Sarkisov Yu.S., Kasatkina A.V. Vliyanie termomodifitsirovannogo torfa na svoistva tsementnykh sistem [Cement paste properties modified by thermally-modified peat additive]. Sukhie stroitel'nye smesi. 2012. No. 1. Pp. 30–31(rus)
Review
For citations:
Dem'yanenko O.V., Kopanitsa N.O., Sorokina E.A. PERFORMANCE CHARACTERISTICS OF 3D PRINTING CONSTRUCTION MIXES DEPENDING ON THERMALLYMODIFIED PEAT ADDITIVE. Vestnik Tomskogo gosudarstvennogo arkhitekturno-stroitel'nogo universiteta. JOURNAL of Construction and Architecture. 2018;(4):122-134. (In Russ.) https://doi.org/10.31675/1607-1859-2018-20-4-122-134
Views:
814
Email this article 